Zyntra
Speaker alignment by Beyond Stereo
Measure actual straight-line distances from both speakers to the same listening position, where their coverage overlaps. The spacing between the speakers is not the distance you need.
Each card has its own main and fill distances, since each listening position is a different distance from the main PA. The main delay, main latency, and temperature in Advanced apply to every card. A different main reference needs a separate setup.
Advanced (temperature, main delay, latency)
Latency means processing/network/DSP latency in the signal path, not including the output delay entered above. Leaving latencies at 0 assumes main and fill paths have matched latency—not that they have zero latency.
Immersive / Atmos speaker alignment
Measure the straight-line distance from each speaker to the same main listening position (head height). Every speaker is delayed to arrive with the farthest one. Level trims follow distance only (inverse-square).
Changing the layout keeps distances for speakers with the same name.
Uses the temperature from Advanced (Fill mode). Subwoofer/LFE is excluded here—use the Subs tab (bass management is typically 80 Hz, LFE low-pass 120 Hz). If your processor has automatic room calibration, verify against its results.
Subwoofer to main alignment
Measure from the sub and from the main (top) to the same listening position where both are about equally loud near the crossover. Usually the nearer one gets delayed.
Advanced for subs
Uses the main existing delay, main latency, and temperature from Advanced on the Fill delay tab. Leave sub latency 0 if sub and main paths have matched latency.
Which crossover frequency?
Start with your speaker manufacturer's recommended preset or crossover; it overrides these general starting points. Set the sub low-pass and the top high-pass to the same frequency.
| Setup | Starting point |
|---|---|
| Live PA, 12–15" tops + subs | 80–100 Hz |
| Small tops (8–10") | 100–120 Hz |
| Atmos / immersive bass management | 80 Hz |
| LFE (.1) channel low-pass | 120 Hz |
| Sub's own low-end (subsonic) filter | Manufacturer setting |
Lower crossovers keep subs from being localized; higher ones take load off small tops. In cinema Atmos, bass-management crossover must not exceed 130 Hz. Sources: QSC, Dolby studio design, Dolby Atmos specs.
Distance alignment is a starting point. Final check at the listening position: play pink noise or a tone at the crossover with sub and top together, flip sub polarity, and keep whichever setting is louder and fuller. Different seats will get different results—this aligns one position only. Cardioid/end-fire sub arrays are not covered.
Spectrum analyzer (RTA)
Play pink noise through the system, stand at the listening position, and hold the phone at ear height pointing at the speakers. Pink noise should look roughly flat; bumps and dips show where to EQ.
Microphone off. Audio is analyzed on this phone only and never recorded or sent anywhere.
Tap or drag on the graph to read a frequency and level.
Yellow bars: live level in relative dB (dimmed bars = phone mic rough there). White ticks: peak hold. Blue dashed line: snapshot. Vertical line + dot: your cursor.
Finer bars (1/12, 1/24) show narrow peaks such as room modes and feedback. They react more slowly, and below about 50 Hz neighboring bars can repeat because the analysis has a resolution limit (~1.5 Hz).
Pink noise generator
Plays from this phone's audio output. To feed the PA, connect the phone's output to a console channel (adapter or Bluetooth receiver). Start low—sustained pink noise can damage speakers and hearing.
Analyzer settings & external mic
Built for the iPhone's own microphone by default. If you plug in a USB measurement mic or audio interface, iPhone uses it automatically; the input name appears above when the browser reports it.
No calibration file loaded.
Only change this to match a real SPL meter. Without that, levels are relative, not dB SPL.
Limits: the iPhone mic is tuned for voice and is not flat—treat readings below about 100 Hz and above about 10 kHz as rough. Levels are relative (uncalibrated). An RTA shows tonal balance only, not timing, phase, or delay; it cannot verify sub alignment. Results apply to where the phone is; move it to a few seats and look for problems common to all.
Export / import setup
Export puts your setup as text below to copy and save (e.g. in Notes). Paste setup text and tap Import to load it.
Accuracy & limitations
Distance-based estimate for the selected listening position. Verify with acoustic measurement when precision matters.
Speed of sound: c = 331.3 + 0.606 × T (°C), m/s, valid here from −20 °C to 50 °C. Feet × 0.3048 = meters. Results show 0.1 ms; 1 inch of measuring error ≈ 0.07 ms, and tape-measure error often exceeds that.
Final fill delay = 1000 × (main − fill distance) ÷ c + main existing delay + main latency − fill latency + intentional lag. It is an absolute setting; the existing fill delay is only used to show how much to add or reduce.
This tool does not: measure actual acoustic arrivals; know your speaker/DSP latency; set your console or processor; align every seat at once; fix room reverberation; or set crossover/subwoofer phase alignment.
About, privacy & feedback
Zyntra is a free speaker-alignment tool from Beyond Stereo Entertainment, a guide to the latest news, tools, and education in immersive audio and immersive entertainment.
Disclaimer: Provided free and as-is, for estimating only. Results depend entirely on the measurements and settings you enter and are not a substitute for acoustic measurement or professional judgment. You are responsible for verifying all system settings, safe sound levels, and equipment limits. Beyond Stereo Entertainment is not liable for any outcome from use of this tool.
Privacy
Zyntra has no accounts, ads, analytics, or tracking. Your setups are saved only on this device (clear them anytime with New setup). The analyzer listens through the mic only while you have it on; sound is analyzed on the phone and is never recorded or sent anywhere. The app connects to the internet only to load and update itself.
Feedback
Found a problem or have an idea? Feedback goes to Beyond Stereo Entertainment.
Send feedback opens your email app with the app version and device type filled in. Nothing is sent until you press Send.
Estimates only—verify before show time. Free tool by Beyond Stereo Entertainment.